1. Minutero
2. Manecilla del día de la semana
3. Manecilla de la hora
4. Manecilla de 24 horas
5. Botón A
6. Corona
7. Corona - Primer chasquido
8. Corona - Segundo chasquido
9. Botón B
10. Visor de la fecha
11. Manecilla de 24 horas del segundo huso horario
12. Segundero

Fijación de la fecha: Mueve la corona a la posición 7 y gírala en el sentido de las agujas del reloj.

Fijación de la hora: Mueve la corona a la posición 8 y gírala.

Fijación de la hora para la esfera de 24 horas Mueve la corona a la posición 8 y gírala.

Fijación del día de la semana: Mueve la corona a la posición 8 y gírala.

Fijación del huso horario: (válido para diferentes franjas horarias) Mueve la manecilla en incrementos de 15 minutos usando el botón A para ir hacia delante y el B para ir hacia atrás.

• Movimiento: Cuarzo Miyota multifunción JP25
• Resistencia al agua: 5 ATM/50 metros
• Funciones: Fecha, día de la semana, formato de 24 horas, otras zonas horarias
• Pila: Sony SR621SW
• Cristal: Vidrio mineral
• Material de la caja: Aleación de zinc
• Material de la correa: Cuero auténtico, acero inoxidable
• Sin níquel: Sí
• Tamaño máximo de la muñeca: Cuero 21 cm, acero 21,5 cm
• Tamaño mínimo de la muñeca: Cuero 15 cm, acero 15,5 cm
• Ancho de la correa: 22 mm
• Diámetro de la caja: 44 mm
• Diámetro de la esfera: 40 mm
• Grosor de la caja: 15 mm
• Altura de la corona: 4 mm
• Ancho de oreja: 22 mm
• Ancho de oreja a oreja: Cuero 50 mm, acero 55 mm
• Peso: Correa de cuero 72 g, correa de acero 161 g

Most watches have some level of water resistance. If your watch isn’t water resistant, it may be able to handle small splashes, but don’t risk it. If it has a leather band, don’t get it wet.

• Do not move the crown or push any buttons when your watch is in contact with water, as this may let water enter the case.
  
• If your watch is not water resistant, dip a cotton swab in a bowl of warm water with a drop or two of soap in. Squeeze the tip of the cotton swab to remove most of the water and gently rub the case.
  
• If your watch is water resistant, soak a soft cloth in a bowl of warm water with two drops of mild washing-up liquid added. Wring most of the water out of the cloth and gently rub the case with it.
  
  

Si tu reloj de metal ha perdido algo de su antiguo lustre, puedes devolvérselo con un paño de microfibra especial para limpiar joyas.

1. Pasa el paño suavemente por la caja y correa para eliminar la suciedad, el polvo o las huellas dactilares.
2. Para zonas de difícil acceso como grabados, bordes y otros detalles, usa un cepillo de dientes suave.
3. Seca el reloj con un paño suave o toalla siempre tras limpiarlo para eliminar elementos tóxicos y evitar que se formen manchas de agua.

As a rule of thumb, genuine leather shouldn’t get wet. This includes sweat and the moisture that evaporates from your body throughout the day, which is why we recommend you don’t wear your leather-strapped watch every day and always take it off when you go to sleep. 1. If you must clean your leather strap, remove it from the case and rub it down with a clean, dry cloth. 2. Apply leather cleaner and conditioner with a soft cloth, gently massaging the lotion into the leather. 3. Finish by wiping with a clean cloth to prevent staining and let the straps air-dry overnight.

Don’t wear it so tight that you have to bend the strap backwards to unbuckle your watch, as this can permanently deform the leather.

• Store your watch in a dark, dry place to avoid corrosion and discolouration of the dial.
• Always replace the battery on a quartz watch as soon as it runs out. With time, an empty battery may start leaking, damaging the watch’s movement.
• Run mechanical watches at least two days a year to prevent gears and cogs from sticking.
• You should always get your watch serviced by a professional every 3 years.

Rule of thumb: Make sure your watch is the last thing you put on and the first thing you take off.

• Take your watch off and store it safely before engaging in any activity that could damage it.
• Take it off before engaging in any activity likely to make you sweat.
• Take it off before you shower, bathe, or go for a swim.
• Take it off before cooking or cleaning.
• Take it off before you go to bed.
• Don’t expose your watch to chemicals such as cologne, sunscreen, perfume, chlorine, hair gel, etc., as these can discolour, stain, or dull surfaces.
• Try to store your watch separately in a soft enclosure to prevent scratching and rubbing.
• If your watch has closures or clasps, close these to prevent tangling.
• Keep your watch stored in a dry, dark place, and avoid heat fluctuation.

Los eslabones que tienen flechas se pueden quitar. Las flechas muestran la dirección hacia la que se deben empujar los pasadores.

1. Usa un quita pasadores y quita el primer pasador. Déjalo a un lado.
2. Decide cuántos pasadores quieres quitar y luego empuja hacia fuera el pasador correspondiente.
3. Quita los eslabones que desees. Cuantos más elimines, más corta será la correa.
4. Conecta los eslabones que queden e inserta el pasador para conectarlos.*

*Es posible que necesites un martillo pequeño para ayudar a colocar el pasador en su lugar.

1. Para realizar ajustes de la longitud precisos con los pasadores de la hebilla, empuja el pasador hacia dentro en uno de los lados y mueve la hebilla ligeramente para fijarlo en su lugar.

2. Repite el proceso en el otro lado de la hebilla.

3. Desliza la hebilla hasta que los pasadores entren en los orificios deseados.

To remove and change your watch strap, you’ll need:

• The watch
• A replacement strap
• A soft surface such as a cloth, t-shirt or mouse pad

You may also need:

• A spring bar tool
• Or a sharp pointed object

1. Place your watch on a soft surface. This prevents it from getting scratched or damaged.

2. If your watch has quick-release pins on the underside, push the small lever inward to release the strap.

1. If your watch has drilled lugs – small holes in the lugs extending from the main watch case – use a sharp, pointed object to push the spring bar in and release the strap. Be careful that the spring bar doesn’t slide out of the strap and get lost.

1. If your watch strap has neither of these, use a spring bar tool. This is a small tool with a v-shaped tip. Use it to compress the spring bar from the underside of the strap between the lugs on the right. Using the tool, push down the ridge of the spring bar to release the strap.

First, check the lug width of your new watch to verify that it’s 22 mm. You can find all our watch straps here. Using the filters, select only the matching width to see our selection for your watch.

If your replacement strap has quick-release bars, press the bar inward and slot it into place between the lugs. You’ll feel it ‘lock’ into position.

If your new strap doesn’t have quick-release pins, use the spring bar tool again. Place one end of the pin into place, then use the tool to compress the spring bar as you slot it in place. You’ll feel it ‘lock’ in position.

Remember to take your time and be careful not to scratch the lugs or damage the new watch strap.

If you take care of your watch and keep it stored correctly, you should enjoy years of timekeeping precision. But even with the best care possible, you may find that your watch needs extra attention from time to time.

Take a look at common issues with watches here. If you can’t find what you’re looking for, our great Customer Service Team is only a phone call away.

Para mantener la validez de la garantía, evita exponer el reloj al agua más allá del límite calculado y conserva el recibo de compra.