1. Hour hand
2. Minute hand
3. Button A
4. Crown
5. Crown - First click
6. Crown - Second click
7. Chronograph 1/20 second hand
8. Button B
9. Date display
10. Chronograph minute hand
11. Chronograph second hand
12. Normal second hand

Set the time: Pull the crown out to position 6 and turn.

Set the Date: Pull the crown out to position 5 and turn.

Using the Chronograph: This chronograph is able to measure and display time in 1/20 second units, up to a maximum of 59min 59sec. The chronograph 1/20-second hand keeps going continuously for 30 seconds after starting and then stops at 0.

Measuring time with the stopwatch:

• Press the A button to start the chronograph.
• The chronograph can be started and stopped sequentially with the A button.
• Press the B button to reset the chronograph and the chronograph's minute and second hands will return to 0.

Chronograph reset (incl. after battery replacement): This procedure should be performed when the chronograph's second hand does not return to 0.

• Pull the crown out to position 6.
• Press the A button once to set the chronograph's second hand to 0.
• Press the B button to set the chronograph's 1/20 second hand to 0. The chronograph hands can be advanced by repeatedly pressing the A or B buttons.
• Once both hands are at 0, return the crown to its normal position.

Additional information: If the date is set between the hours of 21:00 and 01:00, the date may not change on the following day.

• Movement: Miyota 6S30 Quartz Chronograph
• Water resistance: 5 ATM / 50 m / 164 ft
• Features: Date, Chronograph, Stopwatch
• Battery: Sony SR927W
• Glass: Sapphire crystal glass
• Case material: 316L stainless steel case
• Strap material: Stainless steel
• Nickel free: Yes
• Max. wrist size: 8 1/16” (20.4 cm)
• Min. wrist size: 5 7/8” (14.7 cm)
• Strap width: 7/8" (22 mm)
• Case diameter: 1 3/5" (40 mm)
• Dial diameter: 1 3/8” (34 mm)
• Case thickness: 3/8" (10 mm)
• Crown height: 1/5" (4 mm)
• Lug width: 4/5" (20 mm)
• Lug to lug: 2 1/4" (57 mm)
• Weight: 6.7 oz (191 g)

Most watches have some level of water resistance. If your watch isn’t water resistant, it may be able to handle small splashes, but don’t risk it. If it has a leather strap, don’t get it wet.

• Do not move the crown or push any buttons when your watch is in contact with water, as this may let water enter the case.
  
• If your watch is not water resistant, dip a cotton swab in a bowl of warm water with a drop or two of soap in. Squeeze the tip of the cotton swab to remove most of the water and gently rub the case.
  
• If your watch is water resistant, soak a soft cloth in a bowl of warm water with two drops of mild washing-up liquid added. Wring most of the water out of the cloth and gently rub the case with it.
  
  

If your metal watch has lost some of its luster, you can bring it back by polishing it with a special microfibre cloth for cleaning jewelry.

1. Gently wipe down the band and case to remove any dirt, dust, or fingerprints.
2. For areas such as engravings, edges, and other details that are hard to reach, use a soft toothbrush.
3. Always dry your watch with a soft cloth or towel after cleaning to remove pollutants and prevent water spots or stains from forming.

• Store your watch in a dark, dry place to avoid corrosion and discoloration of the dial.
• Always replace the battery on a quartz watch as soon as it runs out. With time, an empty battery may start leaking, damaging the watch’s movement.
• Run mechanical watches at least two days a year to prevent gears and cogs from sticking.
• You should always get your watch serviced by a professional every 3 years.

Rule of thumb: Make sure your watch is the last thing you put on and the first thing you take off. - Take your watch off and store it safely before engaging in any activity that could damage it. - Take it off before engaging in any activity likely to make you sweat. - Take it off before you shower, bathe, or go for a swim. - Take it off before cooking or cleaning. - Take it off before you go to bed. - Don’t expose your watch to chemicals such as cologne, sunscreen, perfume, chlorine, hair gel, etc., as these can discolor, stain, or dull surfaces. - Try to store your watch separately in a soft enclosure to prevent scratching and rubbing. - If your watch has closures or clasps, close these to prevent tangling. - Keep your watch stored in a dry, dark place, and avoid heat fluctuation.

The links with arrows are removable. The arrows show in which direction the pins should be pushed.

1. Use a pin pusher and remove the first pin. Set it aside.
2. Decide how many links you want to remove and then push out the corresponding pin.
3. Remove the undesired link(s). The more links you remove, the shorter the strap will be.
4. Connect the remaining links and insert the pin to connect them.*

*You may need a small hammer to help push the pin into place.

1. To make fine adjustments to the length using the clasp pins, push the pin in on one side and move the clasp slightly to lock it in place.

2. Repeat the process on the other side of the clasp.

3. Slide the clasp until the pins pop into the desired pinholes.

If you take care of your watch and keep it stored correctly, you should enjoy years of timekeeping precision. But even with the best care possible, you may find that your watch needs extra attention from time to time.

Take a look at common issues with watches here. If you can’t find what you’re looking for, our great Customer Service Team is only a phone call away.

To keep the warranty on your watch valid, don't expose it to water past the rated limit and make sure you keep the receipt.